how many miles wide is the usa
Extending nearly halfway around the Northern Hemisphere...
Shocking kills any bacteria that might linger in your pool during the winter. We recommend shocking a few days before you close the pool. If that is not possible, make sure to shock the pool the night before you close it for winter.
Even though your pool will be covered and quiet for the next few months, it’s important to maintain the water and chemical balance before you close it. Closing your pool properly can save you a lot of work and expense when it comes time to open it back up for the summer.
Algaecide should be used after each shock treatment, so it has a better chance to support your chlorine as it works its magic. Be sure to shock your pool first, then when the chlorine levels of your pool return to normal, add the correct amount of algaecide to several places around your pool while your pump is running.
Shocking your pool is easy: Use a shock treatment to bring your 10 to 12 PPM. Then, wait a day or two for the chlorine to come down to its normal level, about 1.5 to 3.5 PPM. Pro tip: For best results, shock your pool a few days before you plan to shut it down.
Often, it will look something like this. 12.5% Liquid Chlorine Pool Shock – Normal Dosage: 1 gallon of shock per 10,000 gallons of water. Shock Dosage: 2 gallons of shock per 10,000 gallons of water. Source: Champion Liquid Pool Shock instructions.
Chlorine levels need to be at 1-3ppm (parts per million) in your pool for the cold winter months. Most pool supply stores recommend using a Chlorine or Non-Chlorine Shock treatment before you close the pool to balance the water and make sure that it’s ready to sit all winter.
Winterizing chemical kit or pH increaser, Alkalinity increaser, Calcium hardness increaser, Pool shock, and Algaecide. Clarifying enzyme supplement (optional, but recommended)
Several days before closing, shock the pool with a chlorine shock or non-chlorine shock, using at least 2 lbs per 10,000 gallons (follow package directions). Allow the chlorine level to return to 1.0-3.0 ppm before adding any winter algaecide or your pool cover.
On the other hand, if you have a mesh pool cover or one that lets in sunlight and fine debris, a better algaecide is a must. If you use chlorine shock to close the pool, it’s best to do so about a week before closing. A very high chlorine level can harm your cover and destroy your algaecide.
Use a jackhammer, sledgehammer, or other tool to smash holes into the bottom of the pool. This will allow water to drain out of it in the future. Remove any top decking concrete walkways, coping tiles and any other concrete around the pool that you don’t want anymore. Toss it into the pool over the holes you have made.
The first thing you’ll want to do before closing your pool is balance the water chemistry. … Also, make sure to thoroughly brush and vacuum the pool and clean your filter by soaking it in a filter cleaner for 24 hours. Next, the day before you close, backwash the filter and then super chlorinate the pool.
If your pool has been green all season you’re probably super excited to close it. While it seems like the easiest option – it’s not! It’s much smarter to close your pool as clean as possible. Algae can grow in water as cold as 50 degrees.
The presence of too much algaecide can lead to a foamy pool water. … Air pockets within the filter system can cause bubbles on the pool surface as well. The bubbles and foam resulting from too much algaecide will be much smaller in size.
Chlorine—yep, your typical sanitizer—is much more effective at killing algae than algaecide is. Even if your water gets cloudy and your walls get slimy, chlorine can still kill it. That’s because chlorine oxidizes bacteria and single-celled algae, which means they trade electrons.
When pool water turns from the clear blue that you are used to seeing into any shade of green, the most frequent reason is algae. A lighter shade of green means that it is likely a fresh formation, but a deeper green could mean a bigger problem.
On average its 2 hours. However this ranges from pool to pool depending on size and cover.
Super chlorinate with liquid chlorine or other chlorine source and add winterizing chemical kit to pool; allow filter to circulate to evenly distribute chemicals. (Use chemicals as labels indicate.) Use 1 gallon of liquid chlorine per 10,000 gallons of pool water.
How much shock do I need to shock my pool? A simple ratio and a standard rule of thumb to follow when you shock your pool is to dissolve one pound of either calcium hypochlorite or sodium dichlor for every 10,000 gallons of pool water.
A: If you just opened your pool, you should add 2 pounds of chlorine per 10,000 gallons of water. To increase the chlorine level in the future, 0.00013 ounces per gallon should be ideal.
The best time of day to add bleach to your pool is at sunset. The purpose of shocking a pool is to quickly increase the concentration of free available chlorine. … You can also simply add more chlorine, and pouring household bleach into the pool is one way to do this.
Pool Collapse – An above ground pool collapse is often caused by the results of ice damage, but it can also happen when there is too much snow accumulated on top of the pool and the frame cannot handle the weight.
During the winter months, the amount of chlorine needed from your salt cell to keep the pool clean is reduced. This is due to the fact that it is difficult for bacteria to grow in cold temperatures.